![]() As it accelerates, several coils around the body glow blue/white while a burst of light appears in front of it. After entering a target date with the keypad inside the DeLorean, the operator accelerates the car to 88 mph (142 km/h), which activates the flux capacitor. The operator is seated inside the DeLorean (except the first time, when the remote control is used), and turns on the time circuits by turning a handle near the gear lever, activating a unit containing multiple fourteen- and seven-segment displays that show the destination (red), present (green), and last departed (yellow) dates and times. NOTE. You should "ALWAYS" install an inline fuse from your power source to protect your unit.ĭated, numbered, signed and autographed on the backside by the artisan.The control of the time machine is the same in all three films. ![]() All of these suggested option will have to plug in to our female power port. If you wish to install the Flux Capacitor into your Delorean for show, you can use a power source such as the cars battery, the cars fuse block or a cigarette lighter plug. If you wish to display your unit in your home or office, you can power it with our optional plug-in electrical AC/DC Power Adapter that plugs into oir provide female power port located on the left side of the unit. Our Flux Capacitor prop replica is powered by any 12vdc power source : We use the same 1980s vintage label maker, glossy red tape and identical font used by the movie prop makers to print these labels "Disconnect Capacitor Drive Before Opening" on the top of the enclosure door & "Shield Eyes From Light" on the enclosure door window. One medium silver located on the top left side, one extra large silver PVC located on the top in the middle, one small located on the top to the right side and one large made Cannon on the side of the enclosureģ correct red enclosure placed labels of: "A" button on the remote will Turn On/Off our Flux Capacitor remotely and 3 buttons of "B, C, D" are to activate various audio featuresĤ movie correct replicated exterior replicated connectors: Wireless 4 button Key Fob remotes included Once the Flux Capacitor has completed the Time Dispersal effect, unit reverts automatically back to the pulsating flux mode. Just as in the movie version, we placed a super bright Xenon LED located in the middle of the three diffuser blocks and a sound byte module for the Temporal Displacement feature. When triggered by our handheld wireless remote or it will be triggered automatically every 88 seconds by our unit simulates when Marty was entering Temporal Displacement mode for time travel by going into "FULL ON" mode giving off a blinding white light from all the LED's in unison with the audio playback for 15 seconds. Temporal Displacement Light & Audio Time Travel mode. One LED in each corner of the internal board totaling four LEDs to give off the same super bright FX as seen in the movie on the Flux Capacitor when the Delorean Time Machine goes into "FULL On" Time Travel mode. We have four super bright white LEDs for the internal general illumination. Internal board General Illumination Lights (GIL) : 6 LEDs placed under each of the 3 diffuser blocks. We place underneath the 3 chaser blocks a total of 18 warm white LEDs for the pulsating movie speed chaser effect. We fabricate these in the same black finish to be screen accurate. Our 3D replicated relay bases and clear acrylic tubes are spot on in every detail. These replicated High Voltage Relays have been cloned using an authentic Torr model TVS-1 relay. Our precise replicated Torr High Voltage Relays: We then remove the hardware from the enclosure, cut out the window, reposition the latches to the film accurate closer together location and professional paint the enclosures to be an exact match to the movie screen Flux Capacitor. We then compared the two and found them to be exactly the same paint match. We also obtained a paint chip from the Flux Capacitor used in the film now located on display at USF. Stahlin was the enclosure used for the movie screen used version however, Stahlin no longer offers the dark grey enclosure so, we obtained a color paint code match from Stahlin of the same paint color code used on the enclosure for the movie. The enclosures is made by Stalin painted battleship dark grey with two quick release latches, movie correct size solid clear "acrylic" window and a screen accurate thick rubber gasket surrounding the window. We engineered our lighting and audio effects (features) to give our Flux Capacitor mesmerizing, eye opening attention, EZ controllable functions and professionally built "ROCK SOLID" with all of these below listed features: Our Flux Capacitor features have been thoroughly researched, verified and authenticated to be extremely screen accurate before we went into production.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |